Two way conveying automatic sand blasting machine
This two-way automatic sand blasting machine is equipped with 32 spray guns. There are 16 guns in the left and right transport tanks respectively, and the spray nozzles with a length of 60 and 10 cm are used for sandblasting automatically. Sandblasting is carried out in a closed box, and each spray gun can be controlled separately.
Selling points of automatic sand blasting machine with two-way conveying:
The two-way conveying automatic sand blasting machine is equipped with sand blasting system, sand stirring system, lifting system, dust removal system, sand dust separation system, electrical control system, two-way conveying system, two-stage separation system and noise treatment system
System, automatic detection system, frequency control system, pressure debugging system, etc.
1. The nozzle in the sandblasting machine system can be used flexibly, and 360 degree unlimited adjustment can be made on the nozzle bracket.
2. The dust removal system adopts bag dust removal (or filter cartridge dust removal), which can effectively absorb the dust from the processing cabin, so that the dust does not overflow.
3. The sand dust separation system can separate the available abrasives from the tiny dust, and the good Abrasives can continue to be used. Separator fan adopts domestic famous brand, long service life and low failure rate.
4. The electrical control system is used to control the electrical of the whole sandblasting machine. All electronic components are genuine ones with long service life and low failure rate.
5. The two-way sandblasting machine is mainly to save the machine area, save processing time, and provide convenience for the products that need to be processed on both sides. The two-way conveying system can be used to transport the products in the left and right directions at the same time. One sandblasting machine is used for two sandblasting machines, and one machine only needs two people to load and unload goods, which greatly saves the labor cost.
6. The machine is equipped with a two-stage separation system to further recover the available sand when spraying fine sand materials, so as to better control the dust overflow in the sand blasting chamber, so as to reduce the production cost and improve the production efficiency. Our factory has applied for a national patent for this technology, and counterfeiting must be investigated.
7. Noise treatment system (our company has applied for a national patent for a special technology, counterfeiting must be investigated) can reduce the noise in the sand blasting process to 68 dB. Give you a comfortable workshop.
8. Automatic detection system is to prevent machine failure, automatic detection of machine fault points. Convenient maintenance.
9. The frequency control system is mainly used to control the sand blasting processing speed, mainly to control the swing speed and conveying speed of the spray gun.
10. The pressure debugging system is designed to make the sandblasting parts achieve different sand feeling and use different spraying force to control the sandblasting pressure.
11. The conveying speed v = 0.4 ~ 1.5m/min, stepless speed regulation by frequency converter, the actual conveying speed is determined by the sand blasting process requirements of the product.
12. The working pressure of the spray gun can be adjusted freely by the pressure regulating valve in the range of 0-7 bar, and the moving speed of the spray gun can be controlled by frequency conversion. The spraying distance L = 0 ~ 250mm, which can be adjusted arbitrarily. The injection angle can be adjusted in the range of (- 30 ° to 30 °).
13. Sand recovery: automatic recovery of available sand, recycling.
14. Dust automatic pulse cleaning, discharge to meet the national environmental protection requirements.
The workers only operate the control system and load and unload the workpiece, and the sandblasting on the surface of the workpiece is automatically completed by the machine. The processing sequence is as follows:
1) . start the fan and add sand.
2) . adjust the height, angle and horizontal distance of the spray gun. Start the electric control system of the machine, start the fan, start the swing mechanism of the spray gun group, and start the conveying mechanism.
3) When the plate enters the sand blasting area, the conveying speed is set well, and the average speed passes through the sandblasting cabin smoothly. The spray gun automatically sandblasting the plate according to the required orientation.
4) The processed workpiece will enter the blowing chamber immediately. The cleaning gun will remove most of the sand and dust remaining on the workpiece, and then output it from the output end.
5) After finishing one side, the worker removes the workpiece from the output end, and then turns the panel over and puts the product into the input end of the other side. After automatic sandblasting, the finished product is taken out. Carry out the next processing again.
Main technical parameters of the machine:
The host structure is made of 3mm-6mm steel plate.
Specification and model: bx1611-16a-dt
Overall dimension of equipment: 4100mm length * 1800mm width * 3300mm height
Equipment room size: 1600mm length * 1700mm width * 800H
Entrance size: 1300mm
Dust box: 1400mm long * 1200mm wide * 2400 high
Power of dust removal fan: 5.5kW 380V, 50Hz
800mm high and 800mm long on both sides
Automatic conveying motor: 1.5kw 380V, 50Hz [speed adjustable by frequency conversion]
Conveying mechanism: 900 * 6000mm is V-belt,
Swing motor: 0.75KW 380V, 50Hz [speed adjustable by frequency conversion]
Lighting: 3 12W LED lights
Number of nozzles: 16 heads (aluminum alloy with carbonization and boron nozzles)
Shell: made of 3mm-10mm steel plate by welding
Windows: 2 frames
Sand hopper: 3
Door: two, front and rear door opening 800mm high * 700mm wide
Sand material type: 30 mesh - 320 mesh abrasive
Air source requirements: the air compressor is more than 12 cubic meters, and the air consumption is required to be 1 cubic meter per nozzle.
Maximum load: 120 kg
Total power: About 7KW
Total weight: about 1.85 tons
after-sale service:
In line with the spirit of "high quality, excellent service and development", Baixiang sandblasting machinery and equipment factory makes a solemn commitment to you with the concept of "high quality products, reasonable price and intimate service" and the principle of responsibility and openness
1. The warranty of the whole machine is one year, except for wearing parts, and it is maintained for life. The company has professional after-sales service personnel, after-sales service is fast, so that you have no aftercare.
2. When delivering goods, explain the function and use of sandblasting machine, shot blasting machine and burr edge machine in detail, teach the customer operation demonstration by hand, and help you to test the sample free of charge, and confirm that the customer will collect money after operation.
3. Regularly return visit to customers, provide lifelong whole process tracking service for users, actively listen to every opinion put forward by customers, and strive to improve solutions. For technical problems that can not be handled by customers, we can help customers sample free of charge.
4. Guarantee period of service commitment: after sales personnel to the scene in time to find out the cause, and quickly give solutions, can deal with in time, immediately. If it can not be handled in time, with the consent of the customer, we will take all possible measures to ensure the operation of the equipment, or need to replace parts or equipment. We promise to replace them unconditionally, and all spare parts within the warranty period are free of charge.
5. Promise after warranty period: users can consult our company's equipment repair and maintenance knowledge at any time. Spare parts only charge cost, and provide consumables at the most favorable price for a long time.
Customized two-way conveying automatic sand blasting machine, please choose Baixiang sand blasting machinery and equipment factory
